High Performance TL(R)Series FGD Pump to Sevilla Factory
Short Description:
Introduction Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD. Samples 600X-TLR: The diameter of discharge: 600mm. bearing lubr...
Product Detail
Product Tags
Related Video
Feedback (2)
High Performance TL(R)Series FGD Pump to Sevilla Factory Detail:
Introduction
Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD.
Samples
600X-TLR: The diameter of discharge: 600mm. bearing lubricating type: thin oil, rubber liner.
700X-TL: The diameter of discharge:700mm, bearing lubricating type: thin oil, metal liner.
Features
- CFD flowing simulating analysis technology is adopted on wetted parts of pump, it has a reliable property and high operational efficiency.
- To adjust bearing assembly can change impeller position in volute, it can keep pump unit in a state of high efficient operation.
- The pump is back pull-out construction, it has easy construction and simplifies maintenance. It can be disassembled without dismantling suction & discharge pipes.
- Double rows taper roller bearings are fitted on pump end, roller bearings are fitted on drive end. Bearings are lubricated by oil which can modify bearing working condition and increase wear life of bearings.
- Mechanical seal adopted is special for cartridge mechanical seal of FGD process.
Technical Parameters
Pump Model |
Capacity Q (m3/h) |
Head H (m) |
Speed n (r/min) |
Max.Eff. (%) |
NPSH (m) |
Outlet Dia./ Inlet Dia. (mm) |
|
1000X- TL(R) |
10440 |
15 |
485 |
89 |
7.0 |
1000/1200 |
|
900X-TL(R) |
15000 |
30 |
485 |
90 |
8.5 |
900/1000 |
|
800X-TL(R) |
9360 |
31 |
485 |
90 |
7.0 |
800/900 |
|
700X-TL(R) |
6840 |
26 |
485 |
87 |
6.0 |
700/800 |
|
600X-TL(R) |
6300 |
25.5 |
620 |
88 |
5.5 |
600/700 |
|
500X-TL(R) |
3750 |
25 |
725 |
85 |
5.0 |
500/500 |
|
400X-TL(R) |
2500 |
25 |
725 |
83 |
5.0 |
400/450 |
|
350X-TL(R) |
1600 |
25 |
960 |
82 |
4.5 |
350/400 |
|
300X-TL(R) |
720-1800 |
15-40 |
450-800 |
60-79 |
2-5.5 |
300/350 |
|
250X-TL |
540-1800 |
20-75 |
450-900 |
75-86 |
2-4 |
250/300 |
|
200R-TL(R) |
360-1000 |
10-40 |
450-980 |
80-85 |
2-5.5 |
200/250 |
|
150R-TL(R) |
200-800 |
15-60 |
600-1200 |
65-80 |
2-5.5 |
150/200 |
|
150E-TL(R) |
150-540 |
12-40 |
800-1480 |
50-67 |
2.5-6 |
150/200 |
|
100E-TL(R) |
70-360 |
15-55 |
800-1600 |
50-68 |
2-6.5 |
100/150 |
|
100D-TL(R) |
20-220 |
10-40 |
800-1800 |
50-65 |
2-4.5 |
100/150 |
|
75D-TL(R) |
40-160 |
10-50 |
1000-2200 |
50-72 |
2-6 |
75-100 |
|
75CC-TL(R) |
30-130 |
8-45 |
900-2400 |
40-57 |
2-6.5 |
75/100 |
|
50D-TL |
70-140 |
25-85 |
850-1450 |
30-47 |
2-6.5 |
50/75 |
|
50CC-TL(R) |
40-85 |
12-64 |
1300-2700 |
40-58 |
2-10 |
50/75 |
|
50BB-TL(R) |
16-75 |
9-44 |
1400-2800 |
35-62 |
2-5.5 |
50/75 |
|
40BB-TL(R) |
32-72 |
6-58 |
1200-3200 |
30-45 |
2-8 |
40/50 |
|
20CC-TL |
16-34 |
25-92 |
1400-2200 |
16-20 |
2-4.5 |
20/40 |
|
20BB-TL(R) |
12.5-28 |
6-68 |
1200-3800 |
20-40 |
2-4.5 |
20/40 |
|
20A-TL(R) |
2.5-10 |
6-37 |
1400-3000 |
15-30 |
20/40 |
Constuction
Sheet One
NO. | Name | Material | NO. | Name | Material |
1 | Support | Cast Iron | 7 | Suction Cover | duplex phase stainless white iron |
2 | Impeller Release Collar | Stainless Steel | 8 | Impeller | duplex phase stainless white iron |
3 | Shaft Sleeve | ZG0Cr18Ni12Mo2Ti | 9 | Cover Plate | QT500-7 Ductile iron |
4 | Mechanical Seal | Hard Alloy | 10 | Frame Plate Liner | Natural Rubber+A3 |
5 | Frame plate Liner Insert | Natural Rubber+A3 | 11 | Frame Plate | QT500-7 Ductile iron |
6 | Cover Plate Liner | Natural Rubber+A3 | 12 | Adaptor Plate | QT500-7 Ductile iron |
Sheet Two
NO. | Name | Material | NO. | Name | Material |
1 | Support | Cast Iron | 7 | Throatbushing | duplex phase stainless white iron |
2 | Impeller Release Collar | Stainless Steel | 8 | Impeller | duplex phase stainless white iron |
3 | Shaft Sleeve | ZG0Cr18Ni12Mo2Ti | 9 | Suction Cover | QT500-7+Rubber |
4 | Mechanical Seal | Hard Alloy | 10 | Cover Plate | QT500-7 Ductile Iron |
5 | Frame plate Liner insert | duplex phase stainless white iron | 11 | Frame Plate | QT500-7 Ductile Iron |
6 | Volute liner | duplex phase stainless white iron | 12 | Adaptor Plate | QT500-7 Ductile Iron |
Material Adopted
Our company developed a kind of new material duplex phase stainless white iron (A49)on FGD device specially. The material has anti-corrosive property of duplex stainless steel and anti-abrasive property of high chrome white iron so that it has remarkable anti-abrasive and anti-corrosive property in FGD process.
Pump casing, pump cover and adaptor plate are bearing pressure parts which are made of ductile iron.
Rubber lined pump: impeller, suction cover/front liner insert are made of duplex phase stainless white iron. Front liner, back liner, back liner insert material is natural rubber which has good anti-corrosive property with light weight, low cost.
Metal lined pump: impeller, volute liner, throatbushing ,frame plate liner insert are made of duplex stainless white iron. Suction cover is made of ductile iron with rubber stuck.
Advantages
- The distinct characteristic of our FGD engineering pump is double-casing and rubber lined technology. Double-casing structure refers that the pump body is divided into outer pump shell and inner lining. The former bears pressure and insulates slurry. The latter contact abrasive and corrosive slurry. we only need to replace the worn out inner liner.
- FGD engineering pump is mainly used to transport limestone and gypsum slurry. This requires the wet part performance well not only in anti-abrasive but also in anti-corrosive. Therefore, the wet parts (such as: impeller, volute liner and frame plate insert, etc.) adopt A49 combined with rubber material. The engineering practice shows that the service life of components made by ours is triple or even higher than the traditional Cr30A products or duplex stainless steel pump.
- A49 material is a kind of abrasive-resistant and corrosive-resistant alloy widely used for FGD projects in the world , the main composition include chromium 28-30%, molybdenum 2-3%, nickel%, carbon 1%, copper is less than or equal to 2%. Corrosive-resistance characteristic: this is given by the austenitic element. In the 70 degree sulfuric acid solution which contains chloride 100000ppm and pH value of 4, the corrosion rate of is 0.5mm/a. In the 60 degree solution which contains 5% nitric, the corrosion rate is 0.5mm/a. In the sodium hydroxide solution at 80 degree and pH value of 13, the corrosion rate is 0.5mm/a. Wear-resistance characteristic: The abrasion performance is given by the chromium carbide on the grain boundary and secondary carbon compounds precipitated on austenite bodies. The abrasion performance is equal to A05, GLH-5, Ni-1.
- TL (R) series FGD engineering pump has the characteristics of uniform parts specifications, widely used in the market, fast delivery, long service time, convenient installation, low cost and so on.
Product detail pictures:
As for aggressive rates, we believe that you will be searching far and wide for anything that can beat us. We can easily state with absolute certainty that for such good quality at such charges we are the lowest around for High Performance TL(R)Series FGD Pump to Sevilla Factory, The product will supply to all over the world, such as: Qatar, Romania, Georgia, In order to meet our market demands, we have paied more attention to the quality of our products and services. Now we can meet customers' special requirements for special designs. We persistently develop our enterprise spirit "quality lives the enterprise, credit assures cooperation and keep the motto in our minds: customers first.
Aeration Systems
Sulzer offers a wide range of aeration systems for municipal and industrial wastewater treatment. Our application and process know-how combined with our unique product portfolio provide customers with high-tech solutions guaranteeing efficiency and process reliability at minimal life cycle cost.
Axially Split Pumps
Sulzer offers a wide range of double suction axially split pumps, which includes both single and multistage designs. Each product range has special design features for targeted industry applications.
Barrel Casing Pumps
Sulzer offers five models of barrel casing pumps: The GSG and CP are for high-temperature hydrocarbon processes, oil production, and offshore crude oil services, the HPcp and HPcpV for water injection to 1000 bar and offshore high energy services, and the HPT for electric utility boiler feed duties.
Control and Monitoring Equipment
In order to achieve optimal operation of different kinds of pumping stations, Sulzer designs pump controllers and control panels with powerful unique features built-in as standard.
MC® Medium Consistency Products
Sulzer MC® Medium Consistency Technology offers a wide range of reliable products for medium-consistency, fibrous slurry applications up to 18% consistency: MCE™, KCE™ and LCE™ pumping systems with patented Fluider™ technology, BM medium consistency and BG degassing pumps, MC® …
Multiphase Pumps
Sulzer helicoaxial multiphase pumps enable boosting of the oil/gas/water mixture from producing wells, without separating the gas from the liquids. They are successfully deployed in remote or subsea location, thus making wells and fields economically viable.
Power Recovery
Many industries aim to reduce their ecological footprint by minimizing energy consumption. Sulzer Hydraulic Power Recovery Reaction Turbines can be used to capture lost energy.
Pumping Stations
The ABS range of pumps and prefabricated, synthetic lifting stations provides an efficient, effective, and economical solution for the removal of wastewater from locations that do not have gravity access to the main sewer line.
Ring Section Pumps
Sulzer has a long tradition of supplying ring section mid- to high-pressure pumps to all kinds of industrial applications. The M-series is designed in a modular way based on different ranges of pressures for use in a wide range of applications, primarily for pumping clean or slightly polluted liquid …
Single Stage Centrifugal Pumps
Our range of single-stage pumps can be designed either using the end suction overhang impeller design method, or the impeller between bearing design method. These pumps comply with either ISO 5199/ISO 2858, ASME B73.1 or API 610 standards and guarantee reliable pumping processes.
Submersible Pumps
Sulzer offers one of the most comprehensive ranges of submersible pumps type ABS available on the market for use within Domestic & Commercial properties, light weight dewatering pumps for mining and construction and a heavy duty range of wastewater pumps suitable for handling high concentrations of rag …
Two-Stage Centrifugal Pumps
Two-stage centrifugal pumps are used in applications where higher head is required. They ensure more reliable, high efficiency process and lower operating costs instead of serial pumping system.
more
Vertical Pumps
Sulzer vertical pumps span flow rates from 8 to 45 000 m3/h (40 to 200 000 US gpm). They generate heads from 2 m to 2 600 m (7 to 8 500 ft), are built with 1 to 40 stages, run at speeds from 180 to 6 000 rpm, and operate in services from -160 to +200 °C (-260 to 400 °F).
我是使用 YouTube 幻灯片制作程序 (https://www.youtube.com/upload) 制作此视频的
By Jerry 2016-9-19 11:11
In China, we have purchased many times, this time is the most successful and most satisfactory, a sincere and realiable Chinese manufacturer!
By Mike 2016-10-22 19:08