factory Outlets for TL(R)Series FGD Pump to Southampton Importers

factory Outlets for
 TL(R)Series FGD Pump  to Southampton Importers

Short Description:

Introduction Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD. Samples 600X-TLR: The diameter of discharge: 600mm. bearing lubr...


Product Detail

Product Tags

Related Video

Feedback (2)

We have now a skilled, performance group to offer excellent support for our consumer. We usually follow the tenet of customer-oriented, details-focused for , , , We aim at Ongoing system innovation, management innovation, elite innovation and market innovation, give full play to the overall advantages, and constantly improve service quality.
factory Outlets for TL(R)Series FGD Pump to Southampton Importers Detail:

Introduction

Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD.

Samples

600X-TLR: The diameter of discharge: 600mm. bearing lubricating type: thin oil, rubber liner.

700X-TL: The diameter of discharge:700mm, bearing lubricating type: thin oil, metal liner.

Features

  1. CFD flowing simulating analysis technology is adopted on wetted parts of pump, it has a reliable property and high operational efficiency.
  2. To adjust bearing assembly can change impeller position in volute, it can keep pump unit in a state of high efficient operation.
  3. The pump is back pull-out construction, it has easy construction and simplifies maintenance. It can be disassembled without dismantling suction & discharge pipes.
  4. Double rows taper roller bearings are fitted on pump end, roller bearings are fitted on drive end. Bearings are lubricated by oil which can modify bearing working condition and increase wear life of bearings.
  5. Mechanical seal adopted is special for cartridge mechanical seal of FGD process.

Technical Parameters

 Pump   Model    

       Capacity          Q  (m3/h)

       Head          H (m)

    Speed          n (r/min)

    Max.Eff.    (%)

        NPSH         (m)

    Outlet Dia./  Inlet Dia.     (mm)

 
 
1000X- TL(R)

10440

15

485

89

7.0

1000/1200

 
900X-TL(R)

15000

30

485

90

8.5

900/1000

 
800X-TL(R)

9360

31

485

90

7.0

800/900

 
700X-TL(R)

6840

26

485

87

6.0

700/800

 
600X-TL(R)

6300

25.5

620

88

5.5

600/700

 
500X-TL(R)

3750

25

725

85

5.0

500/500

 
400X-TL(R)

2500

25

725

83

5.0

400/450

 
350X-TL(R)

1600

25

960

82

4.5

350/400

 
300X-TL(R)

720-1800

15-40

450-800

60-79

2-5.5

300/350

 
250X-TL

540-1800

20-75

450-900

75-86

2-4

250/300

 
200R-TL(R)

360-1000

10-40

450-980

80-85

2-5.5

200/250

 
150R-TL(R)

200-800

15-60

600-1200

65-80

2-5.5

150/200

 
150E-TL(R)

150-540

12-40

800-1480

50-67

2.5-6

150/200

 
100E-TL(R)

70-360

15-55

800-1600

50-68

2-6.5

100/150

 
100D-TL(R)

20-220

10-40

800-1800

50-65

2-4.5

100/150

 
75D-TL(R)

40-160

10-50

1000-2200

50-72

2-6

75-100

 
75CC-TL(R)

30-130

8-45

900-2400

40-57

2-6.5

75/100

 
50D-TL

70-140

25-85

850-1450

30-47

2-6.5

50/75

 
50CC-TL(R)

40-85

12-64

1300-2700

40-58

2-10

50/75

 
50BB-TL(R)

16-75

9-44

1400-2800

35-62

2-5.5

50/75

 
40BB-TL(R)

32-72

6-58

1200-3200

30-45

2-8

40/50

 
20CC-TL

16-34

25-92

1400-2200

16-20

2-4.5

20/40

 
20BB-TL(R)

12.5-28

6-68

1200-3800

20-40

2-4.5

20/40

 
20A-TL(R)

2.5-10

6-37

1400-3000

15-30

 

20/40

 

 

Constuction

TL web

 

Sheet One

  NO.  Name    Material NO.    Name  Material
1 Support  Cast Iron 7 Suction Cover  duplex phase stainless white iron
2      Impeller Release Collar Stainless Steel 8 Impeller   duplex phase stainless white iron
3 Shaft Sleeve ZG0Cr18Ni12Mo2Ti 9 Cover Plate QT500-7 Ductile iron
4      Mechanical Seal  Hard Alloy 10 Frame Plate Liner Natural Rubber+A3
5 Frame plate Liner Insert  Natural Rubber+A3 11 Frame Plate QT500-7 Ductile iron
6 Cover Plate Liner  Natural Rubber+A3 12 Adaptor Plate QT500-7 Ductile iron

Sheet Two

 NO.      Name   Material  NO.   Name    Material
1 Support  Cast Iron 7 Throatbushing     duplex phase stainless white iron
2      Impeller Release Collar  Stainless Steel 8 Impeller  duplex phase stainless white iron
3 Shaft Sleeve ZG0Cr18Ni12Mo2Ti 9 Suction Cover    QT500-7+Rubber
4  Mechanical Seal  Hard Alloy 10     Cover Plate QT500-7 Ductile Iron
5 Frame plate Liner insert duplex phase stainless white iron 11 Frame Plate QT500-7 Ductile Iron
6 Volute liner duplex phase stainless white iron 12 Adaptor Plate QT500-7 Ductile Iron

Material Adopted

Our company developed a kind of new material duplex phase stainless white iron (A49)on FGD device specially. The material has anti-corrosive property of duplex stainless steel and anti-abrasive property of high chrome white iron so that it has remarkable anti-abrasive and anti-corrosive property in FGD process.

Pump casing, pump cover and adaptor plate are bearing pressure parts which are made of ductile iron.

Rubber lined pump: impeller, suction cover/front liner insert are made of duplex phase stainless white iron. Front liner, back liner, back liner insert material is natural rubber which has good anti-corrosive property with light weight, low cost.

Metal lined pump: impeller, volute liner, throatbushing ,frame plate liner insert are made of duplex stainless white iron. Suction cover is made of ductile iron with rubber stuck.

 

TL 3D

 

Advantages

  • The distinct characteristic of our FGD engineering pump is double-casing and rubber lined technology. Double-casing structure refers that the pump body is divided into outer pump shell and inner lining. The former bears pressure and insulates slurry. The latter contact abrasive and corrosive slurry. we only need to replace the worn out inner liner.
  • FGD engineering pump is mainly used to transport limestone and gypsum slurry. This requires the wet part performance well not only in anti-abrasive but also in anti-corrosive. Therefore, the wet parts (such as: impeller, volute liner and frame plate insert, etc.) adopt A49 combined with rubber material. The engineering practice shows that the  service life of components made by ours is triple or even higher than the traditional Cr30A products or duplex stainless steel pump.
  • A49 material is a kind of abrasive-resistant and corrosive-resistant alloy widely used for FGD projects in the world , the main composition include chromium 28-30%,  molybdenum 2-3%, nickel%, carbon 1%, copper is less than or equal to 2%. Corrosive-resistance characteristic: this is given by the austenitic element. In the 70 degree sulfuric acid solution which contains chloride 100000ppm and pH value of 4, the corrosion rate of is 0.5mm/a. In the 60 degree solution which contains 5% nitric, the corrosion rate is 0.5mm/a. In the sodium hydroxide solution at 80 degree and pH value of 13, the corrosion rate is 0.5mm/a. Wear-resistance characteristic: The abrasion performance is given by the chromium carbide on the grain boundary and secondary carbon compounds precipitated on austenite bodies. The abrasion performance is equal to A05, GLH-5, Ni-1.
  • TL (R) series FGD engineering pump has the characteristics of uniform parts specifications, widely used in the market, fast delivery, long service time, convenient installation, low cost and so on.

Product detail pictures:

factory Outlets for
 TL(R)Series FGD Pump  to Southampton Importers detail pictures


Bear "Customer initially, High quality first" in mind, we do the job closely with our customers and supply them with efficient and skilled providers for factory Outlets for TL(R)Series FGD Pump to Southampton Importers, The product will supply to all over the world, such as: Burundi , Rwanda , Sri Lanka , By integrating manufacturing with foreign trade sectors, we can provide total customer solutions by guaranteeing the delivery of right products to the right place at the right time, which is supported by our abundant experiences, powerful production capability, consistent quality, diversified products and the control of the industry trend as well as our maturity before and after sales services. We'd like to share our ideas with you and welcome your comments and questions.


  • Mechanics-eye-view how to replace the power steering pump on a Gen 1 MINI Cooper. Intermittent or failed steering? Out of warranty? Buy parts and install yourself! Have fun by working on your own MINI Cooper!

    Procedure is exactly as shown in this video for all 2002-2006 Coopers and Cooper S hardtops and 2004-2008 Cabriolets.

    MINI USA offered an extended 13 year / 150,000 mile warranty for the following cars. If your car is not in this range, you’re out of luck, but you can save money by doing it yourself!

    Buy a replacement pump here:
    Remanufactured, no core required:

    http://amzn.to/1tPcMT3

    Remanufactured, get a refund for core return:

    http://amzn.to/1wMfda2

    MINI USA offered an extended 13 year / 130,000 mile warranty for 2002-05 MINI Cooper and Cooper S vehicles and model year 2005 Cooper Convertible and Cooper S Convertible vehicles. Check with your MINI dealer for covered VIN ranges.

    If your car is not in this range, it’s not covered by warranty, but you can still save money by doing it yourself!

    Remember to pick up a hose clamp and CHS-11 power steering fluid before starting this job!

    Tools required:
    13mm socket and wrench
    10mm socket / wrench
    T40 socket
    Screwdriver
    Jack and jack stands

    That’s it!

    “DIY MINI Cooper repair videos provided for reference/entertainment purposes only. Only work on your car if you have the right tools and are comfortable doing so. If in doubt, consult a professional. Mod MINI is not responsible for any ‘mistakes’ or ‘incidents’ arising out of your working on your own vehicle. Have fun and stay safe!”

    Follow #ModMINI on Twitter to get notified of new video uploads! https://twitter.com/ModMINIYoutube Thanks for watching!
    Want to show your support for MOD Mini? Go to the channel page (https://www.youtube.com/user/khammo01) and click on the support button! Or, click here for Mod MINI Amazon Registry!

    http://amzn.com/w/2PKRFN62X0RP8



    Recorded: June 2014

    For more information please visit:

    http://www.grundfos.com/service-support.html

    The company comply with the contract strict, a very reputable manufacturers, worthy a long-term cooperation.




    5 Stars By Judy 2016-7-26 18:36
    In our cooperated wholesalers, this company has the best quality and reasonable price, they are our first choice.

    5 Stars By Matthew 2016-11-18 17:10