2017 wholesale price TL(R)Series FGD Pump to Niger Factories

2017 wholesale price  TL(R)Series FGD Pump  to Niger Factories

Short Description:

Introduction Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD. Samples 600X-TLR: The diameter of discharge: 600mm. bearing lubr...


Product Detail

Product Tags

Related Video

Feedback (2)

Our goods are commonly recognized and reliable by consumers and may satisfy continually developing economic and social needs for , , , With a rapid advancement and our buyers come from Europe, United States, Africa and everywhere in the world. Welcome to visit our manufacturing unit and welcome your order, for further more inquires be sure to don't hesitate to get hold of us!
2017 wholesale price TL(R)Series FGD Pump to Niger Factories Detail:

Introduction

Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD.

Samples

600X-TLR: The diameter of discharge: 600mm. bearing lubricating type: thin oil, rubber liner.

700X-TL: The diameter of discharge:700mm, bearing lubricating type: thin oil, metal liner.

Features

  1. CFD flowing simulating analysis technology is adopted on wetted parts of pump, it has a reliable property and high operational efficiency.
  2. To adjust bearing assembly can change impeller position in volute, it can keep pump unit in a state of high efficient operation.
  3. The pump is back pull-out construction, it has easy construction and simplifies maintenance. It can be disassembled without dismantling suction & discharge pipes.
  4. Double rows taper roller bearings are fitted on pump end, roller bearings are fitted on drive end. Bearings are lubricated by oil which can modify bearing working condition and increase wear life of bearings.
  5. Mechanical seal adopted is special for cartridge mechanical seal of FGD process.

Technical Parameters

 Pump   Model    

       Capacity          Q  (m3/h)

       Head          H (m)

    Speed          n (r/min)

    Max.Eff.    (%)

        NPSH         (m)

    Outlet Dia./  Inlet Dia.     (mm)

 
 
1000X- TL(R)

10440

15

485

89

7.0

1000/1200

 
900X-TL(R)

15000

30

485

90

8.5

900/1000

 
800X-TL(R)

9360

31

485

90

7.0

800/900

 
700X-TL(R)

6840

26

485

87

6.0

700/800

 
600X-TL(R)

6300

25.5

620

88

5.5

600/700

 
500X-TL(R)

3750

25

725

85

5.0

500/500

 
400X-TL(R)

2500

25

725

83

5.0

400/450

 
350X-TL(R)

1600

25

960

82

4.5

350/400

 
300X-TL(R)

720-1800

15-40

450-800

60-79

2-5.5

300/350

 
250X-TL

540-1800

20-75

450-900

75-86

2-4

250/300

 
200R-TL(R)

360-1000

10-40

450-980

80-85

2-5.5

200/250

 
150R-TL(R)

200-800

15-60

600-1200

65-80

2-5.5

150/200

 
150E-TL(R)

150-540

12-40

800-1480

50-67

2.5-6

150/200

 
100E-TL(R)

70-360

15-55

800-1600

50-68

2-6.5

100/150

 
100D-TL(R)

20-220

10-40

800-1800

50-65

2-4.5

100/150

 
75D-TL(R)

40-160

10-50

1000-2200

50-72

2-6

75-100

 
75CC-TL(R)

30-130

8-45

900-2400

40-57

2-6.5

75/100

 
50D-TL

70-140

25-85

850-1450

30-47

2-6.5

50/75

 
50CC-TL(R)

40-85

12-64

1300-2700

40-58

2-10

50/75

 
50BB-TL(R)

16-75

9-44

1400-2800

35-62

2-5.5

50/75

 
40BB-TL(R)

32-72

6-58

1200-3200

30-45

2-8

40/50

 
20CC-TL

16-34

25-92

1400-2200

16-20

2-4.5

20/40

 
20BB-TL(R)

12.5-28

6-68

1200-3800

20-40

2-4.5

20/40

 
20A-TL(R)

2.5-10

6-37

1400-3000

15-30

 

20/40

 

 

Constuction

TL web

 

Sheet One

  NO.  Name    Material NO.    Name  Material
1 Support  Cast Iron 7 Suction Cover  duplex phase stainless white iron
2      Impeller Release Collar Stainless Steel 8 Impeller   duplex phase stainless white iron
3 Shaft Sleeve ZG0Cr18Ni12Mo2Ti 9 Cover Plate QT500-7 Ductile iron
4      Mechanical Seal  Hard Alloy 10 Frame Plate Liner Natural Rubber+A3
5 Frame plate Liner Insert  Natural Rubber+A3 11 Frame Plate QT500-7 Ductile iron
6 Cover Plate Liner  Natural Rubber+A3 12 Adaptor Plate QT500-7 Ductile iron

Sheet Two

 NO.      Name   Material  NO.   Name    Material
1 Support  Cast Iron 7 Throatbushing     duplex phase stainless white iron
2      Impeller Release Collar  Stainless Steel 8 Impeller  duplex phase stainless white iron
3 Shaft Sleeve ZG0Cr18Ni12Mo2Ti 9 Suction Cover    QT500-7+Rubber
4  Mechanical Seal  Hard Alloy 10     Cover Plate QT500-7 Ductile Iron
5 Frame plate Liner insert duplex phase stainless white iron 11 Frame Plate QT500-7 Ductile Iron
6 Volute liner duplex phase stainless white iron 12 Adaptor Plate QT500-7 Ductile Iron

Material Adopted

Our company developed a kind of new material duplex phase stainless white iron (A49)on FGD device specially. The material has anti-corrosive property of duplex stainless steel and anti-abrasive property of high chrome white iron so that it has remarkable anti-abrasive and anti-corrosive property in FGD process.

Pump casing, pump cover and adaptor plate are bearing pressure parts which are made of ductile iron.

Rubber lined pump: impeller, suction cover/front liner insert are made of duplex phase stainless white iron. Front liner, back liner, back liner insert material is natural rubber which has good anti-corrosive property with light weight, low cost.

Metal lined pump: impeller, volute liner, throatbushing ,frame plate liner insert are made of duplex stainless white iron. Suction cover is made of ductile iron with rubber stuck.

 

TL 3D

 

Advantages

  • The distinct characteristic of our FGD engineering pump is double-casing and rubber lined technology. Double-casing structure refers that the pump body is divided into outer pump shell and inner lining. The former bears pressure and insulates slurry. The latter contact abrasive and corrosive slurry. we only need to replace the worn out inner liner.
  • FGD engineering pump is mainly used to transport limestone and gypsum slurry. This requires the wet part performance well not only in anti-abrasive but also in anti-corrosive. Therefore, the wet parts (such as: impeller, volute liner and frame plate insert, etc.) adopt A49 combined with rubber material. The engineering practice shows that the  service life of components made by ours is triple or even higher than the traditional Cr30A products or duplex stainless steel pump.
  • A49 material is a kind of abrasive-resistant and corrosive-resistant alloy widely used for FGD projects in the world , the main composition include chromium 28-30%,  molybdenum 2-3%, nickel%, carbon 1%, copper is less than or equal to 2%. Corrosive-resistance characteristic: this is given by the austenitic element. In the 70 degree sulfuric acid solution which contains chloride 100000ppm and pH value of 4, the corrosion rate of is 0.5mm/a. In the 60 degree solution which contains 5% nitric, the corrosion rate is 0.5mm/a. In the sodium hydroxide solution at 80 degree and pH value of 13, the corrosion rate is 0.5mm/a. Wear-resistance characteristic: The abrasion performance is given by the chromium carbide on the grain boundary and secondary carbon compounds precipitated on austenite bodies. The abrasion performance is equal to A05, GLH-5, Ni-1.
  • TL (R) series FGD engineering pump has the characteristics of uniform parts specifications, widely used in the market, fast delivery, long service time, convenient installation, low cost and so on.

Product detail pictures:

2017 wholesale price  TL(R)Series FGD Pump  to Niger Factories detail pictures


It is a great way to further improve our products and repair. Our mission is always to create innovative products to prospects with a superior expertise for 2017 wholesale price TL(R)Series FGD Pump to Niger Factories, The product will supply to all over the world, such as: Hanover, Germany, Andorra, Being the top solutions of our factory, our solutions series have been tested and won us experienced authority certifications. For additional parameters and item list details, be sure to click the button to acquire additional nformation.


  • Please visit https://www.drillingtechnology.org for more information
    THIS IS A SMALL-SCALE PROTOTYPE OF A PROPOSED BALANCED HYDRAULICS REVERSE-CIRCULATOR. IT IS PART OF AN ONGOING R & D EFFORT TO DRIVE DOWN DRILLING COSTS AND REDUCE FORMATION DAMAGE. THE APPROACH HERE IS TO GET THE PUMP PRESSURE OFF THE FORMATION, TO KEEP DRILLING-FLUID SOLIDS AND REWORKED FORMATION SOLIDS OUT OF THE FORMATION, AND TO ENCOURAGE THE DRILLING FLUID TO GO BACK TO THE SURFACE FROM WHERE IT CAME……….MAKING IT POSSIBLE TO DRILL AHEAD WITHOUT EXCESSIVE OVERBALANCE FROM A SURFACE PUMP AND FORMATION-BREAKDOWN.

    THIS SIMPLE INEXPENSIVE ELECTRO-HYDRAULIC INNOVATION IS INTENDED TO PROVIDE FOOD FOR THOUGHT REGARDING THE POSSIBILITY OF REVERSE-CIRCULATING DRILL-CUTTINGS TO THE SURFACE, INCLUDING FINE SAND AND ROCK CHIPS. THE TEST APPARATUS INDICATES IT MAY BE POSSIBLE TO DO SO WITH A LOW-VISCOSITY NEWTONIAN-REFRIGERANT DRILLING FLUID SUCH AS SOLUTION-WEIGHTED BRINE.

    THE 2-INCH-DIAMETER PROTOTYPE, WHICH HAS ONE MOVING PART, PLUS TWO AUTOMATIC CHECK VALVES, IS ENERGIZED BY MEANS OF A 12-VOLT BATTERY CHARGER, SET AT TWO AMPS. BUT THE PROTOTYPE MIGHT BE SCALED-UP TO A DOWNHOLE PUMP FIVE INCHES OR SO IN DIAMETER FOR HYDROCARBON AND GEOTHERMAL DRILLING OPERATIONS. THIS MIGHT BE ACCOMPLISHED WITH MODERATE LEVELS OF ELECTRIC POWER INPUT, OPERATING FOR THE MOST PART, WITHIN THE TOP-HOLE ARTIFICIAL PERMAFROST RIND CREATED BY THE REFRIGERANT HYDRAULICS.

    AT SUCTION-SPALLATION DRILLING DEPTHS, THE REVERSE-CIRCULATORS MIGHT BE INCREASED IN LENGTH TO 20 FEET OR SO IN AN EFFORT TO SEND STRONG UNDERBALANCED PULSE WAVES DOWN THROUGH THE DRILLSTRING T0 THE BOTTOM OF THE HOLE IN AN EFFORT TO FAIL THE ROCK IN TENSION AND EXCAVATE THE BEDROCK WITH MINIMAL ENERGY INPUT.



    Here is a short video of the Beach Replenishment and Dredging at Beach Heaven NJ Long Beach Island. You can see the big CAT bulldozers and other vehicles. They sift the sand to make sure it is safe for the beach goers. This was filmed with my KYOCERA C5170 cell phone. Filmed on May 9, 2016.

    After the signing of the contract, we received satisfactory goods in a short term, this is a commendable manufacturer.





    5 Stars By Steven 2016-6-26 15:38
    Timely delivery, strict implementation of the contract provisions of the goods, encountered special circumstances, but also actively cooperate, a trustworthy company!





    5 Stars By Ricardo 2015-11-03 12:07