11 Years Manufacturer TL(R)Series FGD Pump for British Importers
Short Description:
Introduction Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD. Samples 600X-TLR: The diameter of discharge: 600mm. bearing lubr...
Product Detail
Product Tags
Related Video
Feedback (2)
11 Years Manufacturer TL(R)Series FGD Pump for British Importers Detail:
Introduction
Series of TL FGD pump is a single stage, single suction horizontal centrifugal pump. It is mainly used as the circulating pump for absorbent tower in FGD appliances. It has such features: wide range capacity, high efficiency, better energy saving. This series of pump is matched by tight structure X support which can save much space. Meanwhile our company develops many kinds of materials targeted on the pump for FGD.
Samples
600X-TLR: The diameter of discharge: 600mm. bearing lubricating type: thin oil, rubber liner.
700X-TL: The diameter of discharge:700mm, bearing lubricating type: thin oil, metal liner.
Features
- CFD flowing simulating analysis technology is adopted on wetted parts of pump, it has a reliable property and high operational efficiency.
- To adjust bearing assembly can change impeller position in volute, it can keep pump unit in a state of high efficient operation.
- The pump is back pull-out construction, it has easy construction and simplifies maintenance. It can be disassembled without dismantling suction & discharge pipes.
- Double rows taper roller bearings are fitted on pump end, roller bearings are fitted on drive end. Bearings are lubricated by oil which can modify bearing working condition and increase wear life of bearings.
- Mechanical seal adopted is special for cartridge mechanical seal of FGD process.
Technical Parameters
Pump Model |
Capacity Q (m3/h) |
Head H (m) |
Speed n (r/min) |
Max.Eff. (%) |
NPSH (m) |
Outlet Dia./ Inlet Dia. (mm) |
|
1000X- TL(R) |
10440 |
15 |
485 |
89 |
7.0 |
1000/1200 |
|
900X-TL(R) |
15000 |
30 |
485 |
90 |
8.5 |
900/1000 |
|
800X-TL(R) |
9360 |
31 |
485 |
90 |
7.0 |
800/900 |
|
700X-TL(R) |
6840 |
26 |
485 |
87 |
6.0 |
700/800 |
|
600X-TL(R) |
6300 |
25.5 |
620 |
88 |
5.5 |
600/700 |
|
500X-TL(R) |
3750 |
25 |
725 |
85 |
5.0 |
500/500 |
|
400X-TL(R) |
2500 |
25 |
725 |
83 |
5.0 |
400/450 |
|
350X-TL(R) |
1600 |
25 |
960 |
82 |
4.5 |
350/400 |
|
300X-TL(R) |
720-1800 |
15-40 |
450-800 |
60-79 |
2-5.5 |
300/350 |
|
250X-TL |
540-1800 |
20-75 |
450-900 |
75-86 |
2-4 |
250/300 |
|
200R-TL(R) |
360-1000 |
10-40 |
450-980 |
80-85 |
2-5.5 |
200/250 |
|
150R-TL(R) |
200-800 |
15-60 |
600-1200 |
65-80 |
2-5.5 |
150/200 |
|
150E-TL(R) |
150-540 |
12-40 |
800-1480 |
50-67 |
2.5-6 |
150/200 |
|
100E-TL(R) |
70-360 |
15-55 |
800-1600 |
50-68 |
2-6.5 |
100/150 |
|
100D-TL(R) |
20-220 |
10-40 |
800-1800 |
50-65 |
2-4.5 |
100/150 |
|
75D-TL(R) |
40-160 |
10-50 |
1000-2200 |
50-72 |
2-6 |
75-100 |
|
75CC-TL(R) |
30-130 |
8-45 |
900-2400 |
40-57 |
2-6.5 |
75/100 |
|
50D-TL |
70-140 |
25-85 |
850-1450 |
30-47 |
2-6.5 |
50/75 |
|
50CC-TL(R) |
40-85 |
12-64 |
1300-2700 |
40-58 |
2-10 |
50/75 |
|
50BB-TL(R) |
16-75 |
9-44 |
1400-2800 |
35-62 |
2-5.5 |
50/75 |
|
40BB-TL(R) |
32-72 |
6-58 |
1200-3200 |
30-45 |
2-8 |
40/50 |
|
20CC-TL |
16-34 |
25-92 |
1400-2200 |
16-20 |
2-4.5 |
20/40 |
|
20BB-TL(R) |
12.5-28 |
6-68 |
1200-3800 |
20-40 |
2-4.5 |
20/40 |
|
20A-TL(R) |
2.5-10 |
6-37 |
1400-3000 |
15-30 |
20/40 |
Constuction
Sheet One
NO. | Name | Material | NO. | Name | Material |
1 | Support | Cast Iron | 7 | Suction Cover | duplex phase stainless white iron |
2 | Impeller Release Collar | Stainless Steel | 8 | Impeller | duplex phase stainless white iron |
3 | Shaft Sleeve | ZG0Cr18Ni12Mo2Ti | 9 | Cover Plate | QT500-7 Ductile iron |
4 | Mechanical Seal | Hard Alloy | 10 | Frame Plate Liner | Natural Rubber+A3 |
5 | Frame plate Liner Insert | Natural Rubber+A3 | 11 | Frame Plate | QT500-7 Ductile iron |
6 | Cover Plate Liner | Natural Rubber+A3 | 12 | Adaptor Plate | QT500-7 Ductile iron |
Sheet Two
NO. | Name | Material | NO. | Name | Material |
1 | Support | Cast Iron | 7 | Throatbushing | duplex phase stainless white iron |
2 | Impeller Release Collar | Stainless Steel | 8 | Impeller | duplex phase stainless white iron |
3 | Shaft Sleeve | ZG0Cr18Ni12Mo2Ti | 9 | Suction Cover | QT500-7+Rubber |
4 | Mechanical Seal | Hard Alloy | 10 | Cover Plate | QT500-7 Ductile Iron |
5 | Frame plate Liner insert | duplex phase stainless white iron | 11 | Frame Plate | QT500-7 Ductile Iron |
6 | Volute liner | duplex phase stainless white iron | 12 | Adaptor Plate | QT500-7 Ductile Iron |
Material Adopted
Our company developed a kind of new material duplex phase stainless white iron (A49)on FGD device specially. The material has anti-corrosive property of duplex stainless steel and anti-abrasive property of high chrome white iron so that it has remarkable anti-abrasive and anti-corrosive property in FGD process.
Pump casing, pump cover and adaptor plate are bearing pressure parts which are made of ductile iron.
Rubber lined pump: impeller, suction cover/front liner insert are made of duplex phase stainless white iron. Front liner, back liner, back liner insert material is natural rubber which has good anti-corrosive property with light weight, low cost.
Metal lined pump: impeller, volute liner, throatbushing ,frame plate liner insert are made of duplex stainless white iron. Suction cover is made of ductile iron with rubber stuck.
Advantages
- The distinct characteristic of our FGD engineering pump is double-casing and rubber lined technology. Double-casing structure refers that the pump body is divided into outer pump shell and inner lining. The former bears pressure and insulates slurry. The latter contact abrasive and corrosive slurry. we only need to replace the worn out inner liner.
- FGD engineering pump is mainly used to transport limestone and gypsum slurry. This requires the wet part performance well not only in anti-abrasive but also in anti-corrosive. Therefore, the wet parts (such as: impeller, volute liner and frame plate insert, etc.) adopt A49 combined with rubber material. The engineering practice shows that the service life of components made by ours is triple or even higher than the traditional Cr30A products or duplex stainless steel pump.
- A49 material is a kind of abrasive-resistant and corrosive-resistant alloy widely used for FGD projects in the world , the main composition include chromium 28-30%, molybdenum 2-3%, nickel%, carbon 1%, copper is less than or equal to 2%. Corrosive-resistance characteristic: this is given by the austenitic element. In the 70 degree sulfuric acid solution which contains chloride 100000ppm and pH value of 4, the corrosion rate of is 0.5mm/a. In the 60 degree solution which contains 5% nitric, the corrosion rate is 0.5mm/a. In the sodium hydroxide solution at 80 degree and pH value of 13, the corrosion rate is 0.5mm/a. Wear-resistance characteristic: The abrasion performance is given by the chromium carbide on the grain boundary and secondary carbon compounds precipitated on austenite bodies. The abrasion performance is equal to A05, GLH-5, Ni-1.
- TL (R) series FGD engineering pump has the characteristics of uniform parts specifications, widely used in the market, fast delivery, long service time, convenient installation, low cost and so on.
Product detail pictures:
With our loaded practical experience and thoughtful solutions, we now have been identified for a trusted provider for numerous intercontinental consumers for 11 Years Manufacturer TL(R)Series FGD Pump for British Importers, The product will supply to all over the world, such as: Cook Islands, Israel, South Korea, Due to the stability of our items, timely supply and our sincere service, we are able to sell our merchandise not only over the domestic market, but also exported to countries and regions, including the Middle East, Asia, Europe and other countries and regions. At the same time, we also undertake OEM and ODM orders. We will do our best to serve your company, and establish a successful and friendly cooperation with you.
API certified Coiled Tubing Equipment Manufacturer for PowerReel, Telescopier Spooler, Clip-in-Drum CT Frame, Mandrel, Injector, Control Cabin, Lifting Frame, Hose Reel, PowerPack, Triplex pump, Nitrogen Convertor, Jacking Frame,Centrifugal Pump, Swivel Head, Mixing Tank, Goose Neck, Walking System Frame
MS-04 Mortar Mixing Machine produced by the Perm Plant of Building Machines is designed for making mortar mixtures and lightweight concretes, as well as for their delivering over a distance of up to 150 m from the machine and up to 50 m-height.
A mixer and a buffer tank equipped with a gerotor type pump are compiled in a single production assembly.
Mortar mixture ingredients are loaded into the mixer fitted with external bag breaker.
All ingredients are mixed by spiral blades which can be replaced with cavitating or plough-shaped blades mounted on an all-steel shaft. The shaft is driven in rotation by a 7.5 kW electric motor via a MRV-130 geared motor.
An additional option of the machine is outside-mounted mixer tubes for separate supply of chemical ingredients and water.
The mixing machine is fitted with separate bearing assemblies to keep them clear of abrasive compounds contained in mortar mixtures. The set-up time of bearing assemblies is less than 20 minutes.
The prepared mixture is unloaded through the bottom hole into the buffer tank equipped with the gerotor type pump which is driven in rotation by a 7.5 kW electric motor via a MRV-110 geared motor.
To move within construction site the machine is equipped with rubber wheels.
MS-04 Mortar Mixing Machine produced by the Perm Plant of Building Machines
Mixer capacity: 1000 liters
Capacity of buffer tank fitted with gerotor type pump: 1200 liters
Weight of mortar mixing machine: 950 kg
Power consumption: 15 kW
Machine cost recovery period: 6 months
Warranty period: 24 months
By Carlos 2016-6-08 15:58
The supplier cooperation attitude is very good, encountered various problems, always willing to cooperate with us, to us as the real God.
By Ray 2015-10-15 14:15